NEC Express5800/120Li Uživatelská příručka stáhnout pdf (Strana 76)

72 CAUTIONS AND RESTRICTIONS

166 Communication lost on

enclosure:

Check the connection of the enclosure.

√ √

168 Fan failed on enclosure: Check the operation of the enclosure fan.

√ √

170 Fan removed on enclosure: Check the connection of the enclosure fan.

√ √

171 Power supply failed on

enclosure:

Check the power supply of the enclosure.

√ √

177 Temperature sensor below

warning threshold on enclosure:

The temperature sensor exceeds over the

warning threshold. Check the temperature.

√

178 Temperature sensor below error

threshold on enclosure

The temperature sensor exceeds over the

error threshold. Check the temperature.

√ √

179

Temperature sensor above

warning threshold on enclosure

The temperature sensor exceeds over the

warning threshold. Check the temperature.

√

180

Temperature sensor below error

threshold on enclosure:

The temperature sensor exceeds over the

error threshold. Check the temperature.

√ √

181

Enclosure shutdown: Check the enclosure.

√ √

182

Too many enclosures

connected to port. Enclosure

not supported:

Decrease the number of connected

enclosures.

√

183

Firmware mismatch on

enclosure:

The compatibility with the firmware of the

enclosure is disabled. Contact the support

department.

√ √

184

Sensor bad on enclosure: Contact the support department.

√

185

Phy is bad on enclosure: The enclosure may be defected. Take the

replacement into account.

√ √

186

Unstable Enclosure: The enclosure may be defected. Take the

replacement into account.

√ √

187

Hardware error on enclosure: The enclosure may be defected. Take the

replacement into account.

√ √

188

No response from enclosure: The enclosure may be defected. Take the

replacement into account.

√ √

189

SAS/SATA mixing not

supported in enclosure;

disabled PD:

SAS and SATA coexist in a specific

enclosure. Check whether the connection is

configured correctly.

√

190

Unsupported hotplug was

detected on SES enclosure:

The hot-plug is not supported.

√

195

BBU disabled; changing WB

logical drives to WT

Check the battery.

√

196

Bad block table is 80% full on

PD:

The bad block table in the physical drive is

filled by 80% or larger. Replace the physical

drive.

√ √

197

Bad block table is full; unable to

log block:

The bad block table in the physical drive is

full. Replace the physical drive.

√ √

198

Consistency Check Aborted

Due to Ownership Loss on VD:

Check the authority.

√

199

Background Initialization (BGI)

aborted due to ownership loss

on VD:

Check the authority.

√

200

Battery/charger problems

detected; SOH Bad

Replace the battery.

√ √

201

Single-bit ECC error; warning

threshold exceeded:

Take the preventive replacement of the

physical drive into account.

√ √

202

Single-bit ECC error; critical

threshold exceeded:

Replace the physical drive.

√ √

203

Single-bit ECC error; further

reporting disabled:

Replace the physical drive.

√ √

204 Power supply switched off for

enclosure:

Check the power of the enclosure.

√ √

206 Power supply cable removed on

enclosure:

Check whether the power cable of the

enclosure is disconnected.

√ √

211 BBU Retention test failed! Replace the BBU.

√ √

214 NVRAM Retention test failed! Replace the disk array controller.

√ √

1 2 ... 71 72 73 74 75 76 77

Komentáře k této Příručce

Žádné komentáře

NEC Express5800/120Li Uživatelská příručka Strana 76

Komentáře k této Příručce

Související produkty a manuály pro Disková pole NEC Express5800/120Li